Tnx F5FLN, NX5M, NQ4I.ĬOM port set to 4800 bauds, 8 data bits, no parity, no flow control and 2 stop bits.
When using a "passive" (not powered) interface cable such as the K1NU CAT Control Cable, set DTR to Always OFF, RTS to Always ON. When using a powered CAT interface such as the Yaesu FIF-232C CAT interface box and CT-62 cable, set DTR and RTS to Always OFF. See screen shots of recommended menu settings well-documented by HB9AMO at
#ICOM 756 PRO II CAT CONTROL DOWNLOAD#
Note: Additional function for modern Yaesu rigs is supported by LUA scripts by N6TV that you may download from in file YaesuScripts.zip.ĬOM port set to 4800 bauds, 8 data bits, no parity, no flow control and 2 stop bits.įor DTR and RTS, see FT-1000D below. Use the Icom generic setting with hex address 66h and set COM port to 9600 baud (also successfully tested with 120 baud and TRX set accordingly), 8 data bits, no parity, 2 stop bits. Use the Icom generic setting with hex address 60h and set COM port to 4800 baud, 8 data bits, no parity, 1 stop bit. It uses the same hex address and should work with the same settings. In fact, the IC 7400 (below) is the European version of the IC 746 PRO. Use the Icom generic setting with hex address 38h and set COM port to 1200 baud, 8 data bits, no parity, 1 stop bit. You need to set the Icom rig's address (found in the rig manual) in the wt.ini file in the section. Icom generic: This setting can be used to connect an Icom rig not listed.IC-7400 - not listed, but you may select IC-746 Pro, which uses the same hex address: 66h.(also succesfully tested up to 9600 baud. Tnx F6IFYĬOM port set to 1200 baud, 8 data bits, no parity and 1 stop bit. See also Setting up an Icom IC-275H with the microHAM USB Interface IC.ĬOM port set to 9600 baud, 8 data bits, no parity and 1 stop bit. Another choice is to remove the check mark from both of these options.ĬOM port set to 1200 baud, 8 data bits, no parity and 1 stop bit. The band map then moves very smoothly while turning the VFO. īest results for Icom radios are usually achieved by checking both the Don’t poll and the Use CI-V-Transceive options.
#ICOM 756 PRO II CAT CONTROL WINDOWS#
Note: The VFO-B windows with ICOM is almost always grey on older Icom radios. Note: Additional function for modern Icom rigs is supported by LUA scripts by N6TV that you may download from in file IcomScripts.zip. They all use the same CAT command subset. Virtually, all Icom rigs are supported by Win-Test. (others are known to work, but not fully tested, e.g.TS-2000 – COM port default is 9600 baud, 1 stop bit, RTS=Handshake.For VCP installation instructions, see this page on the Kenwood web site). USB requires installation of the Silicon Labs Virtual COM port (VCP) driver. COM port connection default is 9600 baud. For all other baud rates, use only 1 stop bit. Note: Additional function for modern Kenwood rigs is supported by LUA scripts by N6TV that you may download from in file TS590scripts.zip.Įxception: TS-590S uses two stop bits only for 4800 baud.
They all use the same CAT command subset needed by Win-Test. Virtually all Kenwood rigs are supported by Win-Test.
0 kommentar(er)
